Erosion and Abrasive Machining

25 works

Influence of the Gap between the Serrated Drum and the Bars on the Mechanical Cleaning of Raw Cotton
Ruzimurad Rosulov
ArticleTextile materials and evaluationsRussian Engineering Research20225 citations
ABI
Processing of teeth of saw blades of cotton processing machines with a stream of compressed air with abrasive particles
Illarion Shin, Zokhir Shodmonqulov, S. R. Nazarov +1
ArticleErosion and Abrasive MachiningE3S Web of Conferences20213 citations
ABI
Assessing the surface roughness of parts after shot hardening
M. R. Muminov, D. A. Mamatova, Illarion Shin
ArticleEngineering Technology and MethodologiesRussian Engineering Research20122 citations
ABI
Abrasive blasting of the teeth of linter saws with the aim of their activation
Oybek Ortikov, Zokhir Shodmonkulov, Oysha Kurbonova +2
ArticleErosion and Abrasive MachiningE3S Web of Conferences20231 citations
ABI
Improving impeller and water flow section of vane pumps
Alisher Dzhurabekov, Jaloliddin Rashidov, Aleksandr Gazaryan +3
ArticleEngineering and Agricultural InnovationsE3S Web of Conferences20231 citations
ABI
Substantiation of the drum splitting radius in the areas of fine cotton cleaning of the cleaning unit
Аnvar Djuraev, Sardor Sayitkulov, Javlon Kholmirzaev +2
ArticleEngineering and Agricultural InnovationsAIP conference proceedings20231 citations
ABI
Analysis of the effect of mechanical impurities in water on the hydroabrasive wear of the turbines of the Bozsu hydroelectric power plant
Eduard Kan, Marina Li, Khusnobod Khushvaktova +2
ArticleEngineering and Agricultural InnovationsE3S Web of Conferences20231 citations
ABI
Effect of combined shot peening and ultrasonic nanocrystal surface modification processes on the fatigue performance of AISI 304
Auezhan Amanov, Ruslan Karimbaev, Erfan Maleki +3
ArticleSurface Treatment and Residual StressSurface and Coatings Technology20180 citations
ABI
Investigation of the deformation and strength characteristics of the thread connection in the manufacture of products from fur waste
N Ergasheva, Illarion Shin, Fatima Nigmatova +1
ArticleErosion and Abrasive MachiningIOP Conference Series Earth and Environmental Science20210 citations
ABI
SURFACE MORPHOLOGY OF STEEL SYNTHESIZED BY MELTING A FLAME SUPERSONIC JET OF MIXTURE PROPANE AND AIR GASES
Eshquvat Ulashevich Arziqulov, Sardor Quchqor ugli Eshmamatov
ArticleErosion and Abrasive MachiningEuropean Science Review20220 citations
ABI
Simulation of a single interaction of an abrasive particle with the surface of a part during blasting
Zokhir Shodmonkulov, Khafiza Islomova, Oybek Ortikov +2
ArticleErosion and Abrasive MachiningE3S Web of Conferences20230 citations
ABI
Integrating response surface methodology and machine learning for analyzing the unconventional machining properties of hybrid fiber‐reinforced composites
V. Vinoth, S. Sathiyamurthy, S. Saravanakumar +1
ArticleErosion and Abrasive MachiningPolymer Composites20240 citations
ABI
Topographic analysis of layer erosion in abrasive media
Sardorbek Yusupov, Jamshid Fayzullaev
ArticleErosion and Abrasive MachiningE3S Web of Conferences20240 citations
ABI
RETRACTED: Experiments on pressing elastic-viscous products
Gayrat Bahadirov, Ayder Nabiev, Gerasim Tsoy
ArticleErosion and Abrasive MachiningBIO Web of Conferences20240 citations
ABI
Factors Influencing Cavitation and Abrasive Erosion in Energy-Efficient Pumping System Operation and Performance
Jaloliddin Rashidov, Azam Azimov, Boybek Kholbutaev +3
ArticleErosion and Abrasive Machining20240 citations
ABI
The influence of cavitation on water-abrasive wear of the flow part of centrifugal and axial pumping units
Bakhtiyor Uralov, Oybek Vokhidov, Bobur Shodiev +4
ArticleCoal Combustion and Slurry ProcessingAIP conference proceedings20250 citations
ABI
Selection of Geometric Parameters of Indenters that Provide Sufficient Sensitivity to Changes in Characteristics in the Volume of Material
Tokhir Tursunov, Nodirjon Kayumjonovich Tursunov, А. P. Kren +2
ArticleMetal and Thin Film MechanicsMaterial and Mechanical Engineering Technology20250 citations
ABI
Kinematic structure of the flow in an erosion funnel
Orifjan Bazarov, Yuldash Babazhanov, Iroda Babazhanova +3
ArticleHydrology and Sediment Transport ProcessesAIP conference proceedings20250 citations
ABI
High-Efficiency Ultrajet Hydrodynamic Cracking of Heavy Bitumen and Oil Sludge
I. Yu. Matasova, I. R. Nuritov, A. S. Chulenyov
ArticleUltrasound and Cavitation PhenomenaTikrit Journal of Engineering Sciences20250 citations
ABI
Development of a Novel Erosion Model for Determining Threshold Velocity of Polyphenylene Sulfide (PPS) in Water Injection System
Mohammadreza Karami, Qiuchen Wang, Siamack A. Shirazi +1
ArticleErosion and Abrasive Machining20260 citations
ABI
Mitigating Erosion-Corrosion in CO2 Environments Using Corrosion Resistance Alloys
Anass S. Nassef, Soroor Karimi, Michael W. Keller +1
ArticleErosion and Abrasive Machining20260 citations
ABI
Solid Particle Erosion in Pipeline Expansions: CFD Flow Validation, Mesh Sensitivity, and Experimental Visualization
Abay Bakytov, Jun Zhang, Farzin Darihaki +2
ArticleErosion and Abrasive Machining20260 citations
ABI
CFD Analysis of Erosion in Plugged Tees Series: Effect of Pipe Diameter, Particle Size and Fluid Density
Hassam Ahmad, Jun Zhang, Siamack A. Shirazi +1
ArticleErosion and Abrasive Machining20260 citations
ABI
Critical risk mitigation for toe lasting machines in shoe manufacturing
Indah Apriliana Sari Wulandari, Atikha Sidhi Cahyana, Indri Maulidiyah +2
ArticleErosion and Abrasive MachiningAIP conference proceedings20260 citations
ABI
A Taguchi-based optimization on EDM parameters for enhancing surface roughness in ductile cast iron: Artificial Neural Networks (ANN)-validated approach
Rahul Mehra, Harvinder Singh, Sivasubramanian Palanisamy +9
ArticleAdvanced Machining and Optimization TechniquesJournal of Materials Science Materials in Engineering20260 citations
ABI