Works cited by this work

11 works

Work: Mathematical model of machining errors on CNC lathes

1. Frequency control of asynchronous motors of looms of textile enterprises

   Nurali Pirmatov, Abdullo Panoev

   ArticleEngineering and Agricultural InnovationsE3S Web of Conferences202038 citations

   ABIABI:AkademIndex/openalex/2026.other.060103

2. Best overall dimensions of synchronous generator with permanent magnets for small power wind plants and micro hydropower plants

   Nurali Pirmatov, Shaxnoza Tosheva, Sherzod Toshev

   ArticleElectric Motor Design and AnalysisE3S Web of Conferences201928 citations

   ABIABI:AkademIndex/openalex/2026.other.060100

3. Renewable energy development in Uzbekistan: current status, problems and solutions

   Elyor Saitov

   ArticleEngineering and Agricultural InnovationsE3S Web of Conferences202025 citations

   ABIABI:AkademIndex/openalex/2026.other.080872

4. Experimental study of the control of operating modes of a plate feeder based on the frequency-controlled electric drive

   Olimjon Toirov, Sardor Urokov, Utkir Mirkhonov +2

   ArticleIndustrial Engineering and TechnologiesE3S Web of Conferences202124 citations

   ABIABI:AkademIndex/openalex/2026.other.066206

5. Low - speed generator with permanent magnets and additional windings in the rotor for small power wind plants and micro hydro power plants

   Rustam Baratov, Nurali Pirmatov

   ArticleElectric Motor Design and AnalysisIOP Conference Series Materials Science and Engineering202023 citations

   ABIABI:AkademIndex/openalex/2026.other.047320

6. Trajectory Planning with Obstacle Avoidance of 3 DoF Robotic Arm for Test Tube Handling System

   Hadha Afrisal, Budi Setiyono, Muhammad Fahmi Yusuf +2

   ArticleRobotic Path Planning Algorithms202023 citations

   ABIABI:AkademIndex/openalex/2026.other.051431

7. Optimal model for additional operation of the storage system for photovoltaic wind power plants

   Elyor Saitov

   ArticlePhotovoltaic System Optimization TechniquesE3S Web of Conferences202023 citations

   ABIABI:AkademIndex/openalex/2026.other.080874

8. The mathematical model and a block diagram of a synchronous motor compressor unit with a system of automatic control of the excitation

   Olimjon Toirov, Tulyagan Kamalov, Utkir Mirkhonov +2

   ArticleAdvanced Power Generation TechnologiesE3S Web of Conferences202122 citations

   ABIABI:AkademIndex/openalex/2026.other.060104

9. Analysis of the influence of temperature on the operating mode of a photovoltaic solar station

   Yu M Kurbonov, Elyor Saitov, B. M. Botirov

   ArticlePhotovoltaic System Optimization TechniquesIOP Conference Series Earth and Environmental Science202020 citations

   ABIABI:AkademIndex/openalex/2026.other.080876

10. Overvoltage in the free phase of the stator winding in case of asymmetric short circuit implicit pole synchronous generator biaxial excitation

    Nurali Pirmatov, Sherzod Toshev

    ArticleElectric Power Systems and ControlE3S Web of Conferences201919 citations

    ABIABI:AkademIndex/openalex/2026.other.060101

11. Critical frequency of autonomous current inverter when operating on active-inductive load

    Khushnud Sapaev, Shukhrat Umarov, Islombek Abdullabekov

    ArticleElectric Power Systems and ControlE3S Web of Conferences202019 citations

    ABIABI:AkademIndex/openalex/2026.other.085755